SAE J3068 "Electric Vehicle Power Transfer System Using a Three-Phase Capable Coupler"[1] is a North American recommended practice published and maintained by SAE International. J3068 defines electrical connectors and a control protocol for electric vehicles. It has the formal title "SAE Surface Vehicle Recommended Practice J3068". J3068 defines a system of conductive power transfer to an electric vehicle using a coupler capable of transferring single-phase and three-phase AC power as well as DC power, and defines a digital communication system for control. J3068 also specifies requirements for the vehicle inlet, supply equipment connector, mating housings and contacts.[1]: 1 

SAE 3068
Picture of a mechanically equivalent IEC Type 2 electric vehicle connector (on right). Equivalent SAE terminology for the left connector above is "J3068 DC8 No AC", while the term for the right connector is "J3068 AC6", which refer to the diameters of the 8 mm DC receptacles and the 6 mm AC receptacles.
Type Automotive power connector
Production history
Produced 2018 (SAE J3068 is based on 2009 IEC 62196 Type 2)
General specifications
Pins 7

History

edit

Initial discussions in the Electric Power Research Institute's Infrastructure Working Council meetings regarding issues related to three-phase charging in North America led to the development of J3068. There was a lack of non-proprietary, UL listed equipment that could be legally used in the United States. Some large electric vehicles were being charged without using ground fault protection, and without connectors that automatically de-enegerize when disconnected from the vehicle.[2]

Therefore, SAE authorized a new task force to develop a standard that focused on heavy and medium duty applications, and more generally any vehicle charging at commercial and industrial locations or other places where 3φ power (three-phase) is available and preferred. Early within the development of the standard, it was decided that the J3068 connector and inlet would expand upon Europe's IEC 62196 type 2 connector also known as the Mennekes connector.

Description

edit

The control protocol is a variation of LIN which retains the analog voltage level signaling from SAE J1772. The positive level of the LIN signal waveform can change from 12 volts to 9 or 6 volts (known as State A, State B, and State C in J1772). An earlier version of this LIN-based control protocol was published in Annex D of IEC 61851 edition 3. Major contributors to the development of this protocol include ABB in Sweden, the University of Delaware, Vattenfall Sweden, Mack Trucks/Volvo Trucks North America and others.

SAE J3068 (2018) is written from the point of view of a developer using a commercial LIN development package with API support for LIN functionality (which is familiar to embedded controller programming teams in the automotive industry). The behavior of the EV and EVSE are described separately in terms of the signals they can see on the API. The details of how the LIN signals are sent between the EV and EVSE are assumed to be handled by commercial LIN software.

IEC 61851-1:2017 Annex D does not presume that a commercial LIN development package is used to implement the standard. It leaves the decision how to implement the standard to the developer.

Differences in logic and nomenclature between J3068 and 61851-1 Annex D are detailed in J3068 (2018) Appendix F.

North American Application

edit

J3068 states that it aims to cover three-phase equipment which meets applicable North American listing standards.

The core standards for Electric Vehicle Supply Equipment in North America are tri-national standards for Mexico, Canada, and the United States. See CANENA. They are essentially equivalent documents with different names in each country.

Standard USA Canada Mexico
AC EVSE ANSI/UL 2594 CAN/CSA C22.2 No. 280 NMX-J-677-ANCE
Cordset/cables ANSI/UL 2251 CAN/CSA C22.2 No. 282 NMX-J-678-ANCE
Safety ANSI/UL 2231 CAN/CSA C22.2 No. 281 NMX-J-668-ANCE

[1]: 9  [3]

 
Type 2 connector socket

The J3068 connector is mechanically identical to the Type 2 connector, because it makes direct references to IEC 62196-2 and -3.[4] Additionally, SAE J3068 supports voltage ratings which align with North American grid voltages and EVSE standards.

IEC 62196-2 standard defines the rated operating voltage for AC basic vehicle interface as 250 VAC for single-phase and 480VAC for three-phase, and three-phase EVSE and single-phase vehicles are required to be interoperable. [5] This implies a single-phase EV should be able to charge from a 480VAC three-phase EVSE; however this is mathematically incongruent with the 250 VAC single-phase limit.

   

This means that 480/277 VAC EVSE would exceed the IEC 62196-2 250 VAC single-phase rating even though the 480 VAC three-phase model explicitly supports the operating voltage rating.

Given that a 480Y/277 VAC three-phase wye-connected four-wire supply is a common configuration supplied by utilities at commercial locations – under SAE J3400 and SAE J3068 the implied higher rating is taken; thus allowing single-phase charging at 277 VAC nominal for North American application. Also, SAE J3400 electric vehicles in North America are required to support power transfer under PWM-CP at 277 VAC. [6]

Under SAE J3400 and SAE J3068 EVSE cannot use PWM-CP controls when nominal system voltages exceed 480Y/277 VAC (single-phase 277 VAC). digital communication (e.g. LIN-CP) shall be used when these voltage limits are exceeded (e.g. 600Y/347 VAC – chiefly Canadian).

Specifications[1]: 21–28  J3068 AC6 J3068 DC8 J3068 AC6DC8
Voltage Nominal VAC: 208/120Y 480/277Y 600/347Y Maximum VDC: 1000 See AC6 and DC8
Dimensions EV Inlet IEC 62196-2 Sheet 2-IIf IEC 62196-3 Sheet 3-IVa IEC 62196-3 Sheet 3-IVa
Dimensions EV Connector IEC 62196-2 Sheet 2-IIe IEC 62196-3 Sheet 3-IVc N/A

Digital communication for AC charging (LIN-CP)

edit
 
Second Edition electrical equivalent circuit for connection of LIN nodes to the control pilot circuit with improved PWM compatibility.

Basic AC charging is defined in SAE J1772 and IEC 61851-1 Annex A with an analog control pilot, and is used with a variety of single-phase AC grid voltages lower than 250 VAC. LIN-CP (Local Interconnect Network on the Control Pilot) was originally specified in IEC 61851-1 Annex D in Edition 3. Unlike PLC over Control Pilot (IEC 15118-2), LIN CP is designed to be a low-cost digital upgrade for the analog PWM controls.[1]: 1  [7]

LIN-CP is similar to the approach used by Tesla based on J2411 (Single-wire CAN), but maintains the CP voltage levels from analog PWM to be compatible with existing EVSE safety models.

LIN transceivers used for J3068 must have an extended supply range. For example, the TI SN65HVDA100-Q1 operates from 5V to 27V. The extended voltage range is required because the LIN transceiver must operate when the Control Pilot is at 6V level (similar to "State C" in J1772).[1]: 30–33 

The upcoming second edition of SAE J3068 recommends a slightly different Pilot circuit from the one defined in SAE J1772 to improve compatibility with PWM signaling.[8]

LIN-CP protocol versions
Protocol Version Function Additional info
1 AC - Baseline Initial version published in IEC 61851-1 Annex D (Edition 3 - 2017) (deprecation planned when 61851-1 Edition 4 is published which will be aligned with LIN-CP Version 2)
2 AC - Baseline Commercially deployed version published in SAE J3068
3 AC - J3068/1 Additional ID fields as published in SAE J3068/1[9]
240-251 Proprietary / experimental Add to this list if you made a version
252 AC - J3068/2 Additional ID, V2G and mode fields as published in SAE J3068/2[10]
253 AC - Advanced University of Delaware (V2G, ID, Scheduled departure)

Compatibility

edit
Connection Type ≤ 63 / 70A AND

≤ 480 / 277 V

> 63 / 70A † OR

> 480 / 277 V

Case A - Plug attached to EV LIN-CP / PWM-CP LIN-CP
Case B - Carry-along EV cable LIN-CP / PWM-CP LIN-CP with Cable Node
Case C - Connector Attached to EVSE LIN-CP / PWM-CP LIN-CP*
*Case C with non-current-coded connector (SAE J3400/J1772) can signal up to 80A with PWM-CP

† Power transfer using LIN-CP can exceed the current-coded limit of 63/70A:

  1. If Case B, then a LIN-CP Cable Node with a higher current rating must be present
  2. Verified the LIN-CP connection type implies that no adapters are present

SAE J3068 has additional requirements on the coupler proximity circuit (aka vehicles with Type 2 inlets in North America) that allow them to be interoperable SAE J3400 and SAE J1772 EVSE for both AC and DC power transfer which monitor proximity.  Also, SAE J3068 has additional requirements on the infrastructure proximity circuit (aka socket-outlets EVSE in North America) that allow them to support 48 A carry-along cable assemblies. Both side of the proximity circuit can optionally support 12V power-over-prox (see SAE 3068/2).

SAE J3068, references SAE J3400 for DC power transfer with the appropriate adjustments for the coupler proximity circuit.

Depending on the topology of the vehicle on-board charger, it may be possible to charge from a J1772 EVSE using an adapter.   While adapters are not ideal, manufacturer specific adapters might be useful and are allowed in some countries according to IEC.  Such an adapter should be rated for 80 amps, as there is no practical way to signal the adapter's current rating.  

Deployment example

edit

On 7 November 2018, Greenlots announced a project to provide charging infrastructure for all electric Volvo Trucks in Southern California. "According to Greenlots, the project will be one of the first in North America to demonstrate a new heavy-duty vehicle charging standard, SAE J3068, in real-world applications." See press release.

Equipment availability

edit

Rema USA has ANSI/UL 2251 (USA) and CAN/CSA C22.2 No. 282 (Canada) listed AC6 63A 480VAC three-phase cordsets (52.3 kW), and two DC8 1000VDC cordsets at 125A and 200A. See Underwriters Laboratories listing number E338388.

Nuvve offers three-phase AC EVSE certified to UL and European standards with support for up to 480/277 VAC at 120 amps with SAE J3068 and IEC 61851-1 Annex D compliance, in addition to J1772 and Annex A support at lower voltages. See Maryland Electrical Testing Labs listing number E114798.

Reference implementations and examples

edit

Developers at the University of Delaware's Transport Electrification Center have posted a reference implementation at GitHub SAE J3068 reference implementation which includes hardware and software.

An alternative LDF may be needed for LIN stacks that don't support the same signal appearing in multiple frames. See the Transport Electrification Center Blog for a link.

Proprietary protocols in use

edit

A proprietary version is in use in "behind the fence" applications in North America using protocol version 253. The intention is to deprecate this version when the increased functionality is added to SAE J3068 in an updated edition of the recommended practice in the near future.

References

edit
  1. ^ a b c d e f "SAE J3068 – Electric Vehicle Power Transfer System Using a Three-phase Capable Coupler" (JUL2022 ed.). SAE International. 2022-07-26. {{cite journal}}: Cite journal requires |journal= (help)
  2. ^ McGee, Rodney (April 2, 2018). "UD J3068 Site". EV Center. University of Delaware. Retrieved April 26, 2018.
  3. ^ "New UL Standards Evolving with the Electric Vehicle Industry". UL Blog. Underwriters Laboratories. Retrieved April 26, 2018.
  4. ^ "IEC 62196-3: Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers" (2.0 ed.). International Electrotechnical Commission. Oct 2022. {{cite journal}}: Cite journal requires |journal= (help)
  5. ^ "IEC 62196-2: Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories" (3.0 ed.). International Electrotechnical Commission. October 2022. {{cite journal}}: Cite journal requires |journal= (help)
  6. ^ Rodney McGee (2023-08-31). "SAE J3400: The Standardization of the North American Charging System". SAE International Blog. SAE International. Retrieved 2024-09-03.
  7. ^ "IEC 61851-1: Electric vehicle conductive charging system - Part 1: General requirements" (2.0 ed.). International Electrotechnical Commission. February 2017. {{cite journal}}: Cite journal requires |journal= (help)
  8. ^ "Improved PWM Interoperability in Upcoming Edition of J3068". EV Center. University of Delaware. November 10, 2020. Retrieved November 10, 2020.
  9. ^ "J3068/1_202312: Identification of Vehicles and Supply Equipment for Conductive AC Charging - SAE International". www.sae.org. Retrieved 2024-03-01.
  10. ^ "J3068/2_202401: Control of Bidirectional Power for AC Conductive Charging - SAE International". www.sae.org. Retrieved 2024-03-01.