Potential-induced degradation (PID) is a potential-induced performance degradation in crystalline photovoltaic modules, caused by so-called stray currents. This effect may cause power loss of up to 30 percent.[1]
The cause of the harmful leakage currents, besides the structure of the solar cell, is the voltage of the individual photovoltaic (PV) modules to the ground. In most ungrounded PV systems, the PV modules with a positive or negative voltage to the ground are exposed to PID. PID occurs mostly at negative voltage with respect to the ground potential and is accelerated by high system voltages, high temperatures, and high humidity.
History
editThe term "potential-induced degradation" (PID) was first introduced in the English language in a published study by S. Pingel and coworkers in 2010.[2] It was introduced as a degradation mode resulting from voltage potential between the cells in the photovoltaic module and ground. Research in this field was pioneered by the Jet Propulsion Laboratory, focusing primarily on electrochemical degradation in crystalline silicon [3] and amorphous silicon[4] photovoltaic modules. The degradation mechanism known as polarization found in the first generation crystalline silicon high performance modules from SunPower in strings having positive voltage potential with respect to ground was discussed in 2005.[5] Degradation of conventional front junction (n+/p) solar cell modules under voltage potential was also observed. The degradation by polarization was also covered in the trade journal Photon (4/2006, 6/2006, and 4/2007).
In 2007, PID was reported in a number of solar panels from Evergreen Solar (Photon 1/2008 and 8 /2008). In this case, the degradation mechanism occurring in photovoltaic modules containing the more common front junction (n+/p) crystalline silicon solar cells when the modules were in negative voltage potential with respect to ground. PID was further discussed as a problem in ordinary crystalline modules (Photon 12/2010, lecture by solar energy company Solon SE at PVSEC in Valencia 2010). Statement of the solar module manufacturer Solon SE: "At 1000 V, a now quite common voltage for larger PV systems, it can be critical for each module technology". PID of the shunting type (PID-s), which is the most prevalent and most detrimental type of PID for crystalline silicon modules, was discovered to be caused by microscopic crystal defects penetrating the p-n front junction of affected solar cells.[6]
In 2013, only 4 major manufacturers according to ISE Fraunhofer of the existing 23 modules are considered to be not affected by the PID.[7]
Detection
editAlthough, PID usually has no visual effect on the module, different photovoltaic module analysis techniques are available for detection and analysis. First, the power degradation can become visible in IV curves. infrared thermography and luminescence imaging techniques like electroluminescence and photoluminescence are also able to detect PID.[8]
Prevention
editThe PID-s that occurs in modules in negative polarity strings can be completely prevented if an inverter is used with the possibility of grounding (or effectively grounding) the positive or negative pole. This is possible if the inverter is galvanically isolated, e.g. using a transformer, if specially designed transformerless inverter topologies are used, or by altering the electric grid potential to ground. Which pole must be grounded, is clarified with the solar module manufacturer. The easiest and very effective method to prevent PID is to install a reversal device from the first day of installation. See Anti-PID manufacturers in the "Reversal" section below.
The phenomenon does not affect photovoltaic installations with micro-inverters, as the voltages are too low to facilitate Potential Induced Degradation.[9]
Reversal
editIf the PID effect is present in the solar module, the effect can be reversed. Seven companies, ELETTROGRAF/ATEX , Huawei, OriSolar, VIGDU, iLumen, PADCON and Pidbull have made a device that can prevent and reverse this effect. [10][11][12][13][14]
References
edit^ APID - AntiPID Solution from ELETTROGRAF/ATEX
- ^ Fraunhofer CSP presents results of potential induced degradation (PID) Fraunhofer Center for Silicon Photovoltaics CSP
- ^ Proceedings of the 35th IEEE PVSC 20–25 June 2010 pp. 2817-2822
- ^ http://www2.jpl.nasa.gov/adv_tech/photovol/ppr_81-85/Pred%20Electrochem%20Breakdown%20-%20PVSC1984.pdf [bare URL PDF]
- ^ http://www2.jpl.nasa.gov/adv_tech/photovol/ppr_81-85/Elechem%20Degr%20of%20a-Si%20Modules%20-%20PVSC1985.pdf [bare URL PDF]
- ^ R. Swanson et.al. 15th PVSEC, Shanghai (2005)
- ^ Naumann, Volker; Lausch, Dominik; Hähnel, Angelika; Bauer, Jan; Breitenstein, Otwin; Graff, Andreas; Werner, Martina; Swatek, Sina; Großer, Stephan (2014-01-01). "Explanation of potential-induced degradation of the shunting type by Na decoration of stacking faults in Si solar cells". Solar Energy Materials and Solar Cells. 120, Part A: 383–389. doi:10.1016/j.solmat.2013.06.015.
- ^ FRITZ, Benjamin (2021-01-10). "Dégradation induite par le potentiel PID". Ref : TIP202WEB - "Ressources énergétiques et stockage" (in French). Retrieved 2021-02-16.
- ^ Köntges, Marc; Oreski, Gernot; Jahn, Ulrike; Herz, Magnus; Hacke, Peter; Weiß, Karl-Anders (2017). Assessment of photovoltaic module failures in the field: International Energy Agency Photovoltaic Power Systems Programme: IEA PVPS Task 13, Subtask 3: report IEA-PVPS T13-09:2017. Paris: International Energy Agency. p. 117. ISBN 978-3-906042-54-1. Retrieved 24 June 2020.
- ^ FRITZ, Benjamin (2021-01-10). "Dégradation induite par le potentiel PID". Ref : TIP202WEB - "Ressources énergétiques et stockage" (in French). Retrieved 2021-02-16.
- ^ https://solar.huawei.com/
- ^ iLumen PID BOX mini iLumen nv.
- ^ PADCON PID KILLER PADCON GmbH
- ^ PID Solution for String Inverters Pidbull NV
- ^ PID Solution for Central Inverters Pidbull NV