Norfolk and Western M Class

The Norfolk and Western M, M1 and M2 Classes were a series of 4-8-0 steam locomotives owned and operated by the Norfolk and Western Railway (N&W). The M Classes were primarily assigned to pull the N&W's mainline freight trains, but following the introduction of the railway's Y Class 2-8-8-2's, the M Classes were reassigned to short line freight service.

Norfolk and Western M Class
N&W M Class No. 475 on the Strasburg Rail Road
Type and origin Power type Steam Builder Baldwin Locomotive Works (50); ALCO-Richmond (75) Build date 1906-1907 Total produced 125
Specifications Configuration: ​  • Whyte 4-8-0  • UIC 2'D Gauge 4 ft 8+1⁄2 in (1,435 mm) Leading dia. 27 in (686 mm) Driver dia. 56 in (1,422 mm) Length 74 ft 11+3⁄4 in (22.85 m) Height 15 ft 5 in (4.70 m) Adhesive weight 168,000 lb (76 tonnes) Loco weight 200,000 lb (90.7 tonnes) Fuel type Coal Fuel capacity 40,000 lb (18.1 tonnes) Water cap. 12,000 US gal (45,000 L; 10,000 imp gal) Boiler pressure 200 psi (1,400 kPa) Heating surface 2,940 sq ft (273.1 m2) Cylinders Two Cylinder size 21 in × 30 in (533 mm × 762 mm) Valve gear Stephenson (inside); Some later converted to Baker Valve type 12-inch (300 mm) piston valves
Performance figures Tractive effort 40,163 lbf (178.65 kN)
Career Operators Norfolk and Western Railway Class M Numbers 375–499 Retired 1926 - 1958 Preserved Two (Nos. 475 and 433) preserved, remainder scrapped Disposition No. 475 operational on the Strasburg Rail Road and No. 433 on display

Norfolk and Western M1 Class
Type and origin Only differences from class M above are shown Power type Steam Builder Baldwin (50), ALCO-Richmond (50) Build date 1907 Total produced 100
Specifications Valve gear Walschaerts
Career Operators Norfolk and Western Railway Class M1 Numbers 1000–1099 Retired 1956, 1957 Disposition All scrapped

Norfolk and Western M2 Class
N&W No. 1138 shortly after it was constructed by the Baldwin Locomotive Works
Type and origin Power type Steam Builder Baldwin (50); N&W Roanoke Shops (11) Serial number Roanoke 182–192 Build date 1910 Total produced 61
Specifications Configuration: ​  • Whyte 4-8-0 Gauge 4 ft 8+1⁄2 in (1,435 mm) Driver dia. 56 in (1.422 m) Boiler pressure 200 psi (1.38 MPa) Heating surface 4,041 sq ft (4,315 if superheater fitted) Cylinders Two Cylinder size 24×30 in (540×762 mm) Valve gear Walschaerts (Baldwin built); Baker (Roanoke built)
Performance figures Tractive effort 52,457 lbf (233.34 kN)
Career Operators Norfolk and Western Railway Class M2 Numbers 1100–1160 Retired 1950 - 1957 Preserved Two (Nos. 1118 and 1134) preserved (+ an M2c, No. 1151), remainder scrapped

Overview

Development

By the mid-1900s, the Norfolk and Western Railway (N&W) primarily relied on 2-8-0 "Consolidation" type locomotives to pull the company's heavy freight trains. As freight traffic increased, the N&W decided to place orders for larger locomotives with longer boilers. While 2-8-2 "Mikado" locomotives were made available in the railroad industry by that time, the N&W opted to order locomotives with the 4-8-0 wheel arrangement over the 2-8-2, since they felt putting the weight of the firebox over the rear driving wheels, as opposed to the trailing wheels, would increase adhesion.

Design and construction

The 4-8-0 design the N&W created, classified as the M class, was destined to be an upgrade to the Railway's W2 class 2-8-0's. The pilot axle would carry the lightweight smokebox, and the rear driving wheels would carry the heavyweight 45-square-foot (4 m²) firebox. The firebox would be extended to the back wall of the cab, leaving no room for decks to be installed—this design was similar to those on camelback locomotives, but the fireboxes on the M class were conventional, and the cabs were placed over them, as opposed to ahead of them, like on the camelbacks. The engineer and fireman would have to sit in separate sides adjacent to the firebox while operating an M class, and the fireman would often have to stand on the tender deck while shoveling coal.

The M class locomotives were also equipped with 56-inch (1,422 mm) diameter driving wheels, 21-by-30-inch (533 mm × 762 mm) cylinders, and a boiler pressure of 200 pounds per square inch (1,379 kPa), and the locomotives would be capable of producing 40,163 pounds-force (179 kN) of tractive effort. 75 of the first M class locomotives (Nos. 375-449) were delivered from the American Locomotive Company's (ALCO) Richmond, Virginia works from June 1906 to February 1907, and 50 (Nos. 450-499) were delivered from the Baldwin Locomotive Works of Philadelphia, Pennsylvania from April to August 1906.

Service

The M class would prove to be a mainstay of N&W motive power, working in mainline, transfer, switching, and branch line service. Many members of the class would undergo modifications over the years, such as the addition of higher-capacity tenders, installation of power reverse gear, superheating, and the replacement of the original Stephenson valve gear with that of the Baker type. Popular in service, crews would come to affectionately nickname the locomotives “Mollies,” a moniker which stuck until their retirement in the late 1950s.

Following the initial success of the class Ms, the N&W would order more 4-8-0s of nearly identical design in the form of the M1s in 1907. These differed in their use of Walschaerts valve gear and piston valves in place of slide valves. This design change, however, severely affected the locomotives’ performance, largely due to a poorly-executed design. The valves’ centerlines, being offset from those of the pistons, resulted in excess running gear wear and improper valve timing. Unsurprisingly, as older motive power on the N&W would be phased out, the M1s were among the first to go.

Design shortcomings would plague the subsequent class of 4-8-0s, the M2s, as well. From their arrival in 1910, issues with poor riding qualities and steaming were apparent. Though utilizing a larger boiler than either the Ms or M1s, the M2s possessed a relatively small heating surface area in the firebox, resulting in considerable difficulty in maintaining steam. In spite of the issues (along with subsequent unsuccessful modifications), the M2s lasted in service for considerably longer than the M1s, being among the few larger examples of non-articulated freight power owned by the N&W. The last examples lasted in service until the late 1950s.

Experiments

When larger locomotives arrived on the N&W, some of the M's were sent to work in switching and transfer service. After World War II, however, the N&W began exploring potential replacements, as many of the M’s had begun to show their age; the locomotives also failed to meet smoke abatement laws in many of the cities along the N&W network. In an experiment to address both issues, M2s Nos. 1100 and 1112 were extensively modified between 1947 and 1948, with No. 1100 being modified first. The boilers of both locomotives were rebuilt with shorter flues and combustion chambers. Induced draft fans, driven by steam turbines, were installed, along with mechanical stokers and water level controls; these were added so the locomotives could be left alone for long periods of time and gave rise to the nickname "Automatic Switcher”. Both locomotives were also fitted out with mechanical lubrication and modified tenders, providing an increase in water and coal capacity.

Though extensive, the experiment ultimately proved to be a short-lived failure. Several issues became apparent shortly after No. 1100 reentered service. The blades of the induced-draft fan were quickly eroded by cinders from the locomotive’s fire, and the relatively soft exhaust from the locomotive lead to smoke and ash becoming a frequent source of discomfort for crews. In spite of changes to the design with No. 1112, including increases in heating surface and boiler pressure, along with the installation of a cinder collector to return cinders to the firebox ahead of the induced-draft fan, both locomotives were retired in 1951. The issues encountered in the experiment and the advent of more modern motive power in the form of 0-8-0 switchers (both acquired secondhand from the Chesapeake and Ohio Railway and built in the N&W’s own Roanoke Shops) did little to prolong the service lives of the already subpar M2’s.

Preservation

Two of the N&W's M Class locomotives have been preserved. One M Class, No. 433, is on static display, while the other M, No. 475, is operational and is used in tourist excursion service.

Main article: Norfolk and Western 433

N&W 433 is currently on static display at the trail head of the Virginia Creeper Trail in Abingdon, Virginia.

Main article: Norfolk and Western 475

N&W 475 was restored to operating condition by the Strasburg Rail Road (SRC) in Pennsylvania, and it is being used to pull excursion trains on SRC’s tourist line.

Three of the N&W's M2s have been preserved. Two of these, Both Nos. 1118 and 1151 have yet to be restored from scrapyard condition.

• No. 1134 has been cosmetically restored and is on display at the Railroad Museum of Virginia in Portsmouth, Virginia.
• No. 1118 is currently under the ownership of the National Railway Historical Society’s Roanoke Chapter.
• No. 1151 is part of the Virginia Museum of Transportation’s collection in Roanoke.

See also

• Norfolk and Western A class
• Norfolk and Western J Class (1879)
• Norfolk and Western J Class (1903)

Bibliography

• Carling, D. Rock (1972). 4-8-0 Tender Locomotives. Drake Publishers Inc. ISBN 087749-150-X.
• Rosenberg, Ron; Archer, Eric H. (1973). Norfolk & Western Steam (The Last 25 Years). New York, NY: Quadrant Press, Inc. pp. 11–16, 77–78. ISBN 0-915276-00-3.
• Dressler, Thomas (August 1995). "Norfolk & Western's remarkable 4-8-0s". Railfan & Railroad. Carstens Publications. Archived from the original on 1998-05-08. Retrieved November 10, 2022.